Titanium nanoparticles fate in small-sized watersheds under different land-uses.

Surface waters from three catchments having contrasting land-uses (forested, agricultural, and urban) were sampled monthly and analysed for nanoparticulate titanium dioxide (NPs-TiO2) by single particle ICPMS and electron microscopy. We report one-year of data for NPs-TiO2 having average number and mass concentrations of 9.1 × 108 NPs-TiO2 particles L-1 and 11 µg NPs-TiO2 L-1 respectively. An increase in concentration during warmer months is observed in the forested and agricultural catchments. Both concentrations of NPs-TiO2 are within the range of recently reported values using similar analytical approaches. The positive correlations for NPs-TiO2 mass concentration or particle number with the concentration of some trace elements and DOC in the forested and agricultural catchments suggest the detected NPs-TiO2 in these two systems are mostly from geogenic origin. Additionally, microscopy imaging confirmed the presence of NPs in the three catchments. Furthermore, the land-area normalized annual flux of NPs-TiO2 (1.65 kg TiO2 year-1 km-2) was highest for the agricultural catchment, suggesting that agricultural practices have a different impact on the NPs-TiO2 dynamics and exports than other land-uses (urban or forestry). A similar trend is also found by the reanalysis of recent literature data.

Size measurement of silica nanoparticles by Asymmetric Flow Field-Flow Fractionation coupled to Multi-Angle Light Scattering: A comparison exercise between two metrological institutes.

In this work we present a comparison exercise between two metrological institutes for size measurement of silica nanoparticles by Asymmetrical Flow Field-Flow Fractionation (AF4) coupled to static light scattering. The work has been performed in the frame of a French inter-laboratory comparison (ILC) exercise organized by the nanoMetrology Club (CnM). The general aim of this multi-technique comparison was to improve the measurement process for each technique, after establishing a well-defined measurement procedure. The results obtained by two national metrological institutes (NMIs), the LNE (France) and the SMD (Belgium) by AF4-UV-DRI-MALS will be presented and discussed. Three different samples were characterized: the reference material ERM®-FD304, which is a suspension of colloidal silica in aqueous solution and two silica bimodal samples consisting of two populations of SiO2 nanoparticles of unknown size in aqueous solution, with different populations' ratios. The procedure for the preparation of the sample before the analysis, and main separation parameters have been previously defined between the two institutes and will be described. The principals measured parameters were the weight-average (dge_w), number-average (dge_n) and z-average (dge_z) geometric diameter; the average hydrodynamic diameter (dh); and the diameter obtained by external calibration using polystyrene latex standards (dcal). Results between the two NMIs were comparable and coherent with the expected size values of those obtained by other techniques like Scanning Mobility Particle Sizer (SMPS) and Scanning Electron Microscopy (SEM) also involved in this ILC exercise. Where discrepancies are observed, they leave the results compatible within their uncertainties and underpin the challenges in analysing data and reporting results, making AF4 a powerful tool to compare to other measurement techniques.

Biotransformation of Food-Grade and Nanometric TiO2 in the Oral-Gastro-Intestinal Tract: Driving Forces and Effect on the Toxicity toward Intestinal Epithelial Cells.

Background: Oral exposure to titanium dioxide (TiO2) is common since it is widely used in food and pharmaceutical products. Concern on the safety of this substance has been recently raised, due to the presence of an ultrafine fraction in food-grade TiO2. Discrepancy exists among data reported in in vitro and in vivo studies on intestinal acute/chronic toxicity of TiO2. This might be due to the different biological identity of TiO2 in traditional in vitro test by respect in vivo conditions. Methods: One food-grade TiO2 and two nanometric TiO2 samples were treated with a simulated human digestive dystem (SHDS) in order to investigate the bio-transformation occurring to the particles once ingested in term of size distribution (Dynamic Light Scattering-DLS-, Flow Particle Imaging, Asymmetric Flow Field Flow Fractionation-AF4-) and surface modification (Electrophoretic Light Scattering-ELS-, Electron Paramagnetic Resonance Spectroscopy-EPR-). The effect of SHDS on the cyto-, genotoxicity and potential to induce oxidative stress towards human colorectal carcinoma HCT116 cells was also assessed. Results: Aggregation as a consequence of the high ionic strength of the gastric and intestinal simulated fluids was observed, together with the formation of a partially irreversible bio-corona containing phosphate ions and proteins. Such bio-corona led to a partial masking of the TiO2 particles surface and reactivity. Pristine and treated TiO2 nanoparticles showed comparable acute toxicity and genotoxicity toward HCT116 cells, whereas a small decrease of the induction of oxidative stress after treatment was observed. Conclusions: Overall the results underline the importance of SHDS as a tool to improve the predictive power of in vitro tests towards intestinal nanomaterial toxicity.

Flow and fate of silver nanoparticles in small French catchments under different land-uses: The first one-year study.

This study focused on surface waters from three small creeks, within the Seine River watershed, which are characterized by different land-uses, namely forested, agricultural and urban. Silver nanoparticles (Ag-NPs) in these waters were detected and quantified by single-particle ICPMS during one-year of monthly sampling. Their temporal and spatial variations were investigated. Ag-NPs, in the three types of surface water, were found to range from 1.5 × 107 to 2.3 × 109 particles L-1 and from 0.4 to 28.3 ng L-1 at number and mass concentrations, respectively. These values are in consistent with the very few previous studies. In addition, the role of factors driving process and potential sources are discussed with correlations between Ag-NPs concentrations and biogeochemical parameters, like dissolved organic carbon concentration and divalent cations concentrations. For the forested watershed NOM controls the stability (number and mass) of the Ag-NPs as recently observed in the field in lake water in Germany. In the case of the agricultural and urban watersheds major cations such as Ca would control the number and mass of Ag-NPs. Dilution processes are rejected as conductivity and Cl- ions do not show significant correlations with Ag-NPs or other major geochemical parameters. The specific exportation rates of Ag-NPs for artificial, agricultural and forested areas were calculated based on the monthly data for the full year and are equal to 5.5 ± 3.0, 0.5 ± 0.3 and 0.2 ± 0.2 gy-1km-2, respectively. These data suggest a constant release of Ag-NPs from consumer products into freshwaters in artificial areas, for instance, from textiles, washing machines, domestic tap-water filters, outdoor paints. These first data of Ag-NPs fluxes in surface waters of France enlarge the very limited database of field measurements. Moreover, for the first time, the influence of time, land-use and aquatic geochemistry parameters on Ag-NPs in real natural water samples is reported. It is also helpful to further understand the fate and the process of Ag-NPs in natural waters, as well as to the ecotoxicity studies in real-world environment.

Theoretical and experimental investigation of the focusing position in asymmetrical flow field-flow fractionation (AF4).

To better understand the focusing process and to determine the focusing position (zfoc) in Asymmetrical Flow Field-Flow Fractionation (AF4), theoretical and experimental studies were performed. A new theoretical expression that allows the calculation of zfoc in AF4 channels of any shape having an axial plane of symmetry was established. The equation was then applied to the particular case of a trapezoidal AF4 channel with tapered ends. The applicability of this equation was verified by comparing the calculated results with the experimental measures of the focusing position obtained using blue dextran dye under different flow conditions. The calculated values and the experimental results were in good agreement. The total uncertainty associated with the calculated zfoc was evaluated and was lower than 10%. A good repeatability and reproducibility of the focusing position was obtained. Moreover, the effects of the sample-injection position, the spacer thickness, the membrane aging, and the nature of the injected sample on the focusing position were investigated: zfoc was not influenced by these parameters, proving the universal applicability of the equation given in this work for predicting the focusing position, when the assumption of constancy of the cross-flow velocity at the membrane, which underlies this equation, is fulfilled. Additionally, it is notable that this theoretical expression is suitable for different models of AF4 channel and not peculiar to specific suppliers.

Towards tributyltin quantification in natural water at the Environmental Quality Standard level required by the Water Framework Directive.

The European Union (EU) has included tributyltin (TBT) and its compounds in the list of priority water pollutants. Quality standards demanded by the EU Water Framework Directive (WFD) require determination of TBT at so low concentration level that chemical analysis is still difficult and further research is needed to improve the sensitivity, the accuracy and the precision of existing methodologies. Within the frame of a joint research project "Traceable measurements for monitoring critical pollutants under the European Water Framework Directive" in the European Metrology Research Programme (EMRP), four metrological and designated institutes have developed a primary method to quantify TBT in natural water using liquid-liquid extraction (LLE) and species-specific isotope dilution mass spectrometry (SSIDMS). The procedure has been validated at the Environmental Quality Standard (EQS) level (0.2ngL(-1) as cation) and at the WFD-required limit of quantification (LOQ) (0.06ngL(-1) as cation). The LOQ of the methodology was 0.06ngL(-1) and the average measurement uncertainty at the LOQ was 36%, which agreed with WFD requirements. The analytical difficulties of the method, namely the presence of TBT in blanks and the sources of measurement uncertainties, as well as the interlaboratory comparison results are discussed in detail.

Determination of tributyltin in whole water matrices under the European Water Framework Directive.

Monitoring of water quality is important to control water pollution. Contamination of the aquatic system has a large effect on human health and the environment. Under the European Water Framework Directive (WFD) 2000/60/EC and the related directive on environmental quality standards (EQS) in the field of water policy 2008/105/EC, the need for sensitive reference methods was highlighted. Since tributyltin (TBT) is one of the WFD listed priority substances a method was developed which is capable to qualify and quantify the pollutant at the required low WFD EQS of 0.2ngL(-1) in whole water bodies, i.e. in non-filtered water samples with dissolved organic carbon and suspended particulate matter. Therefore special attention was paid on the interaction of TBT with the suspended particulate matter and humic substances to obtain a complete representation of the pollution in surface waters. Different water samples were investigated varying the content of organic dissolved and suspended matter. Quantification was performed using species-specific isotope dilution (SSID) and gas chromatography with inductively coupled plasma mass spectrometry (GC-ICP-MS). Different sample treatment strategies were evaluated and compared. The process of internal standard addition was investigated and optimized, hence the equilibrium between internal standards and matrix is of primary importance to perform accurate SSID. Samples spiked at EQS level were analyzed with a recovery between 95 and 105 %. Additionally real surface water samples were investigated and the TBT concentration for the whole water body was determined and compared with conventional routine analysis method.

Experimental design for TBT quantification by isotope dilution SPE-GC-ICP-MS under the European water framework directive.

In Europe the maximum allowable concentration for tributyltin (TBT) compounds in surface water has been regulated by the water framework directive (WFD) and daughter directive that impose a limit of 0.2 ng L(-1) in whole water (as tributyltin cation). Despite the large number of different methodologies for the quantification of organotin species developed in the last two decades, standardised analytical methods at required concentration level do not exist. TBT quantification at picogram level requires efficient and accurate sample preparation and preconcentration, and maximum care to avoid blank contamination. To meet the WFD requirement, a method for the quantification of TBT in mineral water at environmental quality standard (EQS) level, based on solid phase extraction (SPE), was developed and optimised. The quantification was done using species-specific isotope dilution (SSID) followed by gas chromatography (GC) coupled to inductively coupled plasma mass spectrometry (ICP-MS). The analytical process was optimised using a design of experiment (DOE) based on a factorial fractionary plan. The DOE allowed to evaluate 3 qualitative factors (type of stationary phase and eluent, phase mass and eluent volume, pH and analyte ethylation procedure) for a total of 13 levels studied, and a sample volume in the range of 250-1000 mL. Four different models fitting the results were defined and evaluated with statistic tools: one of them was selected and optimised to find the best procedural conditions. C18 phase was found to be the best stationary phase for SPE experiments. The 4 solvents tested with C18, the pH and ethylation conditions, the mass of the phases, the volume of the eluents and the sample volume can all be optimal, but depending on their respective combination. For that reason, the equation of the model conceived in this work is a useful decisional tool for the planning of experiments, because it can be applied to predict the TBT mass fraction recovery when the experimental conditions are drawn. This work shows that SPE is a convenient technique for TBT pre-concentration at pico-trace levels and a robust approach: in fact (i) number of different experimental conditions led to satisfactory results and (ii) the participation of two institutes to the experimental work did not impact the developed model.

Effects of extraction methods on the composition and molar mass distributions of exopolymeric substances of the bacterium Sinorhizobium meliloti.

The influence of the extraction methods on the composition, size diversity, molar mass and size distributions of exopolymeric substances (EPS) from the bacterium Sinorhizobium meliloti wild type (WT) and by the exoY strain deficient in exopolysaccharide production was investigated. EPS obtained by centrifugation, EDTA and formaldehyde/NaOH were compared. It was found that the extraction method influenced TOC, TN and total protein content in EPS from both strains. However, no difference between EDTA and formaldehyde/NaOH methods was observed for the exopolysaccharide components. Similar functional groups and fluorescence pattern were found in the EPS obtained by different methods; however their relative abundance was method dependent. The extraction method also affected the molar mass and size distribution, HP SEC diversity among different treatment and bacterial strains.

Characterization of the colloidal organic matter from the Amazonian basin by asymmetrical flow field-flow fractionation and size exclusion chromatography.

Colloidal organic matter (COM) collected in small and large watercourse tributaries of the Negro River (Brazil) were fractionated and characterized by an asymmetrical flow field-flow fractionation (AFlFFF) coupled to UV and seven angle laser light scattering (LS) detectors, and by size exclusion chromatography (SEC) coupled with a UV detection. Number and weight average molar masses, weight average gyration radiuses R(Gw) and polydispersity indexes were obtained for each sample in two separate runs under conditions optimized for lower and larger size fractions. The results demonstrate the existence of a decrease of size of the colloidal matter when passing from first order streams to higher order rivers. No significant changes were found in size distributions of samples collected during the low and high flow stages at the same site. The influence of selected pre-treatments such as filtration and reverse osmosis pre-concentration on the size and molar mass distributions was also studied.

Asymmetrical flow field-flow fractionation coupled to multiangle laser light scattering detector: optimization of crossflow rate, carrier characteristics, and injected mass in alginate separation.

The coupling of the flow field-flow fractionation (FlFFF) to differential refractive index (DRI) and multiangle laser light scattering (LS) detectors is a powerful tool for characterizing charged polysaccharides such as alginate. However, the correct interpretation of the experimental results and extrapolation of meaningful molecular parameters by using an analytical tool with such a level of complexity requires improvement of the knowledge of the alginate behavior in the channel and careful optimization of the operating conditions. Therefore, the influence of the critical operating parameters, such as crossflow rate, carrier composition and concentration, and sample load, on the alginate retention was carefully evaluated. Combined information obtained simultaneously by DRI and LS detectors over the wide range of the crossflow rate, carrier liquid concentration, and injected amount, allowed to set the appropriate combination of optimal parameters. It was found that the crossflow rate of 0.25 mL/min, carrier solution containing 5x10(-2 )mol/L ammonium or sodium chloride, and 50-100 microg of injected sample mass were necessary to achieve complete separation and determination of the meaningful molecular characteristics. The values of the weight-average hydrodynamic radius (R(Hw)), radius of gyration (R(G)), and molar mass (M), obtained under the optimal conditions were in good agreement to those found for alginates in the literature.